PRODUCT NO. 6000-QD

  • Quick Dry Formula for abnormal weather conditions
  • An ultra white acrylic roof coating that forms a thick rubber-like shield
  • Offers excellent weatherproof protection due to its maximum resistance to ponded water conditions and high reflectivity
  • 10-Year limited manufacturers warranty

COMPLIES WITH:

compliance

astm

crrc

Sale!

$98.00 $96.00

Login / Register for Additional Discounts

  • Quick Dry Formula for abnormal weather conditions
  • An ultra white acrylic roof coating that forms a thick rubber-like shield
  • Offers excellent weatherproof protection due to its maximum resistance to ponded water conditions and high reflectivity
  • 10-Year limited manufacturers warranty

COMPLIES WITH:

compliance

astm

crrc

Clear

Description

DESCRIPTION. PRODUCT NO. 6000 Quick Dry is a durable 100% acrylic elastomeric roof coating in a quick dry version than can withstand light to moderate rain within 15-30 minutes. PRODUCT NO. 6000 Quick Dry is designed for maximum protection against sun and extreme weather. Its bright white fi nish enables it to defl ect the sunʼs heat and harmful UV rays, protecting the roof substrate and lowering energy bills. PRODUCT NO. 6000 Quick Dry forms a thick, rubber-like shield that expands and contracts greater than 220% to prevent cracking and slow the aging process. PRODUCT NO. 6000 Quick Dry resists cracking, peeling, and mildew while providing excellent protection against extreme weather.

USES. PRODUCT NO. 6000 Quick Dry can be used directly over spray polyurethane foam and most previously coated roof surfaces. PRODUCT NO. 6000 Quick Dry should not be applied over 100% silicone. When applying over aluminum roof coating, asphalt, tar, hot applied built-up roofi ng, granulated cap sheet, and metal roofi ng systems, TPO, or EPDM follow surface preparation instructions below.

SURFACE PREPARATION. Roof substrates must be clean, dry, free of all debris, and any contaminants which would impede proper adhesion. A pressure wash is recommended, if a pressure washer is not available a cleaning agent should be used in conjunction with hose and broom washing. In addition to pressure washing, a wire brush should be used to remove any surface rust on metal roofi ng systems. Metal panels where the structural integrity has been compromised should be removed and replaced with like panels. A bleach and water solution (1 part bleach to 2 parts water) should be used to treat any roof areas that have mildew or algae. All roof surfaces should be thoroughly cleaned and allowed to dry completely prior to application of any Tucson Rubberized Coatings products. Over aluminum roof coating, asphalt, tar, hot-applied built-up roofi ng, granulated cap sheet, and metal roofi ng systems, one coat of PRODUCT NO. 295-G STAIN SHIELD or PRODUCT NO. 297-X X-TREME must be applied prior to the application of PRODUCT NO. 6000 Quick Dry. All large cracks and seams should be repaired by embedding one layer of polyester fabric between two layers of PRODUCT NO. 501-W-P ACRYLIC MASTIC or PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC prior to application of PRODUCT NO. 6000 Quick Dry. To achieve proper adhesion over TPO, PVC, or EPDM, one coat of PRODUCT NO. 297-X X-TREME must be applied prior to any Tucson Rubberized Coatings repair or top coat products.

APPLICATION. Proper protective clothing and PPE should be worn when applying products. It is normal to see a small amount of separation when fi rst opening a pail. If necessary, gently mix the product with a roller frame or paddle mixer, being careful to not introduce air into the product during mixing. Product can be applied by roller (3/4 – 1 1/4” nap), brush, and spray equipment capable of 2000 – 3000 PSI and 1-3 GPM of output. For best results when spraying, an 8-31 or -8-41 reversible spray is recommended. Do not dilute product. Tucson Rubberized Coatings Products should not be applied when freezing temperatures or rain is expected within 24 hours of completed application. During application, roof surface temperatures should be between 40 and 115 degrees Fahrenheit, with no moisture present.

RECOMMENDED COVERAGE RATES (completed in 2 coats): PRODUCT NO. 6000 Quick Dry should be applied at a minimum rate of 1 – 1 ½ gallons per 100 square feet of roof surface, per coat. The fi rst coat should be allowed to cure approximately 24 hours before a second coat is applied. The second coat should be applied perpendicular to the fi rst coat (cross hatch application). Two coats applied at the specifi ed rate are required to obtain a Limited Manufacturer Material Warranty. Coverage rates will depend on porosity of the roofi ng substrate. Final Dry Film Thickness (DFT) will

DO NOT APPLY TO ANY SURFACES THAT CONTAIN SILICONE.

STORAGE: Product should be stored in a clean and dry area, away from direct sunlight and protected from freezing.

CLEAN-UP: Clean brushes, tools and other equipment with warm soapy water immediately after use. Dried fi lm may require paint remover.

HANDLING PRECAUTIONS: Product safety information required for safe use is not included. Before handling, read product safety data sheets and container labels for safe use, physical and health hazard information. Safety data sheets are available on the TRC website at www.rubberized.com. You can also obtain a copy from one of our local TRC stores.

Additional information

Weight58 lbs
Dimensions13 × 13 × 16 cm
Weight per Gallon

11.4 lbs

Solids by Weight*

71%

Drying Time (50% Relative Humidity & 70°F)

Touch/2.5 hrs – Firm/5 hrs minimum

Flammability

None

Wet Film

None

VOC

< 150 grams/liter

Elongation

>300%

Tensile Strength

300 PSI

Viscosity

120 KU

*NOTE:

Percentages stated are + or – 5%

Approx. Shipping Weights:

(All approximate weights include container)
5 gallons 58 lbs.

Color

tan, white

Size

5 Gallon

Share your thoughts!

Let us know what you think...

What others are saying

There are no contributions yet.

×

Login

Continue as a Guest