Original price was: $125.00.$115.00Current price is: $115.00.
Description
USES: PRODUCT NO. 570 can be used as a puddle filling compound for voids and gaps in seams and joints, around penetrations, drains, scuppers and creating sloped crickets.
SURFACE PREPARATION: Roof substrates must be clean, dry, free of all debris, and any contaminants which would impede proper adhesion. A pressure wash is recommended, if a pressure washer is not available a cleaning agent PRODUCT NO. 750-15OZ should be used in conjunction with hose and broom washing. In addition to pressure washing, a wire brush should be used to remove any surface rust on metal roofing systems. All roof surfaces should be thoroughly cleaned and allowed to dry completely prior to application of any Tucson Rubberized Coatings products. To achieve proper adhesion over TPO, PVC, EPDM, spray polyurethane foam, aluminum roof coating, asphalt, tar, hot-applied built-up roofing, granulated cap sheet and metal roofing systems one coat of PRODUCT NO. 297-X X-TREME must be applied prior to the application of PRODUCT NO. 570. All large cracks and seams should be repaired by embedding one layer of polyester fabric between two layers of PRODUCT NO. 501-W-P ACRYLIC MASTIC or PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC prior to application of PRODUCT NO. 570.
INSTRUCTION GUIDE:
- Open bucket and remove- Bag, brush, gloves and paper.
- Place bag over bucket and empty contents into bag- Remove resin.
- Prior to mixing, ensure surface is clean, dry and damage free. For maximum adhesion, apply 297-x Primer prior to application.
- Once you’re ready to mix, place gloves on and empty resin into bag. Remove ALL of the resin into the bag.
- Give contents a quick mix with your hands or knead bag to combine the product thoroughly. Hint- Mix should be done with-in 15 mins of opening resin. While kneading, allow space in bag for product to tumble.
- Dump product into low areas and spread with trowel or tool. Compact product to provide a solid form. Scrape and compact to level or create slope.
- Repeat for desired results.
- Once Product has dried(12-24hrs) apply 2 coats of Tucson Rubberized Top Coat to ensure product longevity.
DO NOT APPLY TO ANY SURFACES THAT CONTAIN SILICONE.
STORAGE: Product should be stored in a clean and dry area, away from direct sunlight and protected from freezing.
COMPLIES WITH: ASBESTOS FREE
HANDLING PRECAUTIONS: Product safety information required for safe use is not included. Before handling, read product safety data sheets and container labels for safe use, physical and health hazard information. Safety data sheets are available on the TRC website at www.rubberized.com. You can also obtain a copy from one of our local TRC stores.
LIMITED WARRANTY AND DISCLAIMER: To the best of our knowledge, the technical data contained herein is true and accurate at the date of issuance and is subject to change without prior notice. User must contact TRC to verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. Liability, if any, is limited to replacement of product unless installed by an approved contractor in accordance with TRC warranty procedures and program. For limited manufacturer’s warranty and disclaimer information, visit our website at: www.rubberized.com.
Additional information
Weight | 50 lbs |
---|---|
Dimensions | 15 × 15 × 18 in |
Silicone (%) | None |
Flammability | None |
VOC | < 50 g/I |
Viscosity | 80-90 KU |
Comments are closed.
One reply on “Product No. 570 Green Slope Elevating Compound For Low Spots”
We used this product to patch a few low spots on our flat roof and it worked amazingly well. We followed the instructions on the site and application was simple and easy. I would imagine that this is the same type of roof patching compound that contractors in Tucson would use. Thank you TRC!