Product No 510 High Viscosity Patching Compound

  • High viscosity is ideal for application on vertical surfaces
  • A premium quality elastomeric patching compound
  • Combines acrylic polymers with a high solid content with polyester fibers
  • Can be used as a patching compound for filling voids and for filling gaps in parapet walls, sealing around penetrations, or for sealing drains and scuppers
SAVE 8%
Tucson Rubberized Coating product 510

From $27.85

Login / Register for Additional Discounts

  • High viscosity is ideal for application on vertical surfaces
  • A premium quality elastomeric patching compound
  • Combines acrylic polymers with a high solid content with polyester fibers
  • Can be used as a patching compound for filling voids and for filling gaps in parapet walls, sealing around penetrations, or for sealing drains and scuppers
In Stock. Ready for Delivery.

Description

DESCRIPTION. PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC is an elastomeric premium quality white sealing compound designed for use in the waterproofing of roof flashings. PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC is reinforced with polyester fibers for maximum strength and durability while remaining flexible.

USES. PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC can be used as a patching compound or flashing mastic for sealing around roof penetrations, pipes, skylights, ductwork, or filling gaps in parapet walls with excellent adhesion to most roofing substrates. PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC can also be used in conjunction with a polyester fabric for added strength around penetrations, drains, scuppers, and skylights.

SURFACE PREPARATION. Roof substrates must be clean, dry, free of all debris, and any contaminates which would impede proper adhesion. A pressure wash is recommended, if a pressure washer is not available a cleaning agent should be used in conjunction with hose and broom washing. In addition to pressure washing, a wire brush should be used to remove any surface rust on metal roofing systems. Metal panels where the structural integrity has been compromised should be removed and replaced with like panels. Over aluminum roof coating, apply one coat of PRODUCT NO. 295-G STAIN SHIELD or PRODUCT NO. 297-X XTREME prior to the application of PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC. Over TPO, EPDM, and PVC apply one coat of PRODUCT NO. 297-X X-TREME prior to the application of PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC. A bleach and water solution (1 part bleach to 2 parts water) should be used to treat any roof areas that have mildew or algae. All roof surfaces should be thoroughly cleaned and allowed to dry completely prior to application of any Tucson Rubberized Coatings restoration products.

APPLICATION. Proper protective clothing and PPE should be worn when applying products. It is normal to see a small amount of separation when first opening a pail. If necessary, gently mix the product with a trowel or paddle mixer, being careful to not introduce air into the product during mixing. PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC can be applied with a stiff paint brush or trowel in conjunction with a polyester fabric for reinforcement. Do not dilute product. While PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC is white and UV stable, to extend its life it is recommended that it be coated by one of Tucson Rubberized Coatings topcoats. Tucson Rubberized Coatings Products should not be applied when freezing temperatures or rain is expected within 24 hours of completed application. During application, roof surface temperatures should be between 40 and 115 degrees Fahrenheit, with no moisture present.

DO NOT APPLY TO ANY SURFACES THAT CONTAIN SILICONE.

CLEAN-UP. Clean brushes, tools, and other equipment with warm soapy water immediately after use. Dried film may require paint remover.

Additional information

Weight 67 kg
Dimensions 15 × 15 × 18 cm
Weight per Gallon

10.9 lbs

Solids by Weight*

66%

Drying Time (At 50% relative humidity and 70°F)

Touch: 4 hrs, Firm: 24 hrs

Flammability

None

VOC

< 50 g/I

Viscosity

>160 KU

*NOTE:

Percentages stated are + or – 5%

Approx. Shipping Weights:

(All approximate weights include container)
5 gallon bucket weight approximately 58 lbs.

Color

Tan, White

Size

1 Gallon, 3.5 Gallon, 5 Gallon

Quick Comparison

SettingsProduct No 510 High Viscosity Patching Compound removePRODUCT NO. 295-G STAIN BLOCKING PRIMER removeTIETEX POLYESTER ROOFING MEMBRANE - REINFORCEMENT ROOFING FABRIC removeProduct No 910 Flashing Sealant removePRODUCT NO. 302 ACRYLIC TOPCOAT remove901 - PS SELF-ADHESIVE UNDERLAYMENT | FLEECE TOP PEEL & STICK remove
ImageTucson Rubberized Coating product 510Acrylic saturant and Substrate primer product no 7000Tietexa910 productEnviro coat roof coating product no. 302901ps product
SKU510295OW5324W4302W5901
Rating
PriceFrom $27.85

Login / Register for Additional Discounts

$70.00

Login / Register for Additional Discounts

From $26.50

Login / Register for Additional Discounts

From $390.00

Login / Register for Additional Discounts

From $71.00

Login / Register for Additional Discounts

$157.50

Login / Register for Additional Discounts

Stock
Availability
Add to cart

Buying Options

Add to cart

Buying Options

Buying Options

Buying Options

Add to cart

Description
  • High viscosity is ideal for application on vertical surfaces
  • A premium quality elastomeric patching compound
  • Combines acrylic polymers with a high solid content with polyester fibers
  • Can be used as a patching compound for filling voids and for filling gaps in parapet walls, sealing around penetrations, or for sealing drains and scuppers
  • Recommended for priming over asphalt based surfaces as well as concrete, metal, and aged roof coatings to prevent bleed through to the top coating
  • A penetrating sealer designed to provide a firm surface for application of wall coatings
  • Can be used to install polyester for complete roofing system
  • Which primer is right for me
  • 4" x 324'
  • 6" x 324'
  • 12" x 324'
  • 20" x 324'
  • 40" x 324'
  • Tietex polyester fabric is a stitch-bonded, high-performance fabric
  • Used in applied built-up roofing and roof maintenance systems using either water-based asphalt, acrylic emulsions, or solvent type coatings or mastic
  • The polyester fabric is white with lay lines for one and two-ply roof systems
  • 100% acrylic with flexibility and reflectivity to protect the roof surface
  • Reduces interior temperatures
  • Reduces home cooling expenses
  • 5-Year limited manufacturers warranty

BENEFITS:

  • Ideal for repairs & ponding areas
  • Self-sealing membrane
  • Promotes maximum TRC topcoat adhesion
  • Excellent for use under metal or tile applications

PRODUCT DETAILS:

  • Waterproof membrane
  • Hurricane/wind resistant
  • Promotes maximum TRC topcoat adhesion
  • 257 Degree heat resistance
Content

DESCRIPTION. PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC is an elastomeric premium quality white sealing compound designed for use in the waterproofing of roof flashings. PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC is reinforced with polyester fibers for maximum strength and durability while remaining flexible.

USES. PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC can be used as a patching compound or flashing mastic for sealing around roof penetrations, pipes, skylights, ductwork, or filling gaps in parapet walls with excellent adhesion to most roofing substrates. PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC can also be used in conjunction with a polyester fabric for added strength around penetrations, drains, scuppers, and skylights.

SURFACE PREPARATION. Roof substrates must be clean, dry, free of all debris, and any contaminates which would impede proper adhesion. A pressure wash is recommended, if a pressure washer is not available a cleaning agent should be used in conjunction with hose and broom washing. In addition to pressure washing, a wire brush should be used to remove any surface rust on metal roofing systems. Metal panels where the structural integrity has been compromised should be removed and replaced with like panels. Over aluminum roof coating, apply one coat of PRODUCT NO. 295-G STAIN SHIELD or PRODUCT NO. 297-X XTREME prior to the application of PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC. Over TPO, EPDM, and PVC apply one coat of PRODUCT NO. 297-X X-TREME prior to the application of PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC. A bleach and water solution (1 part bleach to 2 parts water) should be used to treat any roof areas that have mildew or algae. All roof surfaces should be thoroughly cleaned and allowed to dry completely prior to application of any Tucson Rubberized Coatings restoration products.

APPLICATION. Proper protective clothing and PPE should be worn when applying products. It is normal to see a small amount of separation when first opening a pail. If necessary, gently mix the product with a trowel or paddle mixer, being careful to not introduce air into the product during mixing. PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC can be applied with a stiff paint brush or trowel in conjunction with a polyester fabric for reinforcement. Do not dilute product. While PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC is white and UV stable, to extend its life it is recommended that it be coated by one of Tucson Rubberized Coatings topcoats. Tucson Rubberized Coatings Products should not be applied when freezing temperatures or rain is expected within 24 hours of completed application. During application, roof surface temperatures should be between 40 and 115 degrees Fahrenheit, with no moisture present.

DO NOT APPLY TO ANY SURFACES THAT CONTAIN SILICONE.

CLEAN-UP. Clean brushes, tools, and other equipment with warm soapy water immediately after use. Dried film may require paint remover.

DESCRIPTION: Product No. 295-G STAIN SHIELD is a light gray, highly elastomeric asphalt stain shield and fabric saturant with excellent adhesion to new and existing asphalt roof systems; granulated modified bitumen; SPF (uncoated and acrylic coated); and metal. Product No. 295-G STAIN SHIELD is excellent for liquid applied polyester fabric overlay systems and should be used as a base coat, not being left exposed to the suns UV rays for extended periods of time.

USES: Product No. 295-G STAIN SHIELD is to be used as a base coat primer over asphalt, tar, hot-applied built-up roofing, granulated cap sheet, steel, and aluminum roofing substrates. Product No. 295-G STAIN SHIELD can also be used as a fabric saturant when installing a fabric overlay system.

SURFACE PREPARATION: Roof substrates must be clean, dry, free of all debris, and any contaminates which would impede proper adhesion. A pressure wash is recommended, if a pressure washer is not available a cleaning agent should be used in conjunction with hose and broom washing. In addition to pressure washing, a wire brush should be used to remove any surface rust on metal roofing systems. Metal panels where the structural integrity has been compromised should be removed and replaced with like panels. A bleach and water solution (1 part bleach to 2 parts water) should be used to treat any roof areas that have mildew or algae. All roof surfaces should be thoroughly cleaned and allowed to dry completely prior to application of any Tucson Rubberized Coatings restoration products.

APPLICATION: Proper protective clothing and PPE should be worn when applying products. It is normal to see a small amount of separation when first opening a pail. If necessary, gently mix the product with a roller frame or paddle mixer, being careful to not introduce air into the product during mixing. Product can be applied by roller (3/4 - 1 1/4" nap), brush, and spray equipment capable of 2000 - 3000 PSI and 1 - 3 GPM of output. For best results when spraying, an 8-31 - 8-41 reversible spray is recommended. Do not dilute product. Tucson Rubberized Coatings Products should not be applied when freezing temperatures or rain is expected within 24 hours of completed application. During application, roof surface temperatures should be between 40 and 115 degrees Fahrenheit, with no moisture present.

RECOMMENDED COVERAGE RATES (completed in 2 coats): Product should be applied at a minimum rate of 1 -1.5 gallons per 100 square feet of roof surface, per coat. When used as a fabric saturant, Product No. 295-G STAIN SHIELD should completely saturate the fabric by embedding the fabric between two coats at a minimum of 1 - 1.5 gal per 100 square feet per coat. Coverage rates will depend on the porosity of the roofing substrate.

DO NOT APPLY TO ANY SURFACES THAT CONTAIN SILICONE.

STORAGE: Product should be stored in a clean and dry area, away from direct sunlight and protected from freezing.

CLEAN-UP: Clean brushes, tools, and other equipment with warm soapy water immediately after use. Dried film may require paint remover.

PHYSICAL PROPERTIES: Bleed-Blocking Primer and Fabric Saturant

HANDLING PRECAUTIONS: Product safety information required for safe use is not included. Before handling, read product safety data sheets and container labels for safe use and health hazard information. Safety data sheets are available on the TRC website at: www.rubberized.com.

LIMITED WARRANTY AND DISCLAIMER: To the best of our knowledge, the technical data contained herein is true and accurate at the date of issuance and is subject to change without prior notice. User must contact Tucson Rubberized Coatings to verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. Liability, if any, is limited to replacement of product unless installed by an approved contractor in accordance with Tucson Rubberized Coatings warranty procedures and program. For limited manufacturer's warranty and disclaimer information, visit our website at: www.rubberized.com.

SIZE. 4" x 324'

DESCRIPTION. Tietex polyester roofing membrane is a reinforcement roofing fabric that is white with lay lines for one and two-ply roof systems. It offers an unusual combination of high-strength properties, and it also delivers good elongation for excellent thermal stress force accommodations.

USES. Tietex polyester fabric is a stitch-bonded, high-performance fabric for use in applied built-up roofing and roof maintenance systems using either water-based asphalt, acrylic emulsions, or solvent type coatings or mastic.

Made in the USA. If you would like to learn more about this exceptional roofing product, then get in touch with Tucson Rubberized Coatings today. We will be glad to answer your questions. If you need help finding the right coating product, then our team can help!

DESCRIPTION: PRODUCT NO. 910 FLASHING SEALANT is a high performance one-part, moisture curing, and room temperature vulcanizing (RTV) 100% silicone flashing sealant combined with reinforcing materials to provide strong seal-ability around roof fasteners, transitions and penetrations. PRODUCT NO. 910 FLASHING SEALANT has ultrahigh strength and remains very durable. It will maintain its integrity on fasteners and penetrations with movement. PRODUCT NO. 910 FLASHING SEALANT exhibits excellent unprimed adhesion to concrete, metals and most other roofing substrates, provided they are clean, dry and free of dust and frost. PRODUCT NO. 910 FLASHING SEALANT is unaffected by sunlight (ultra-violet rays), ozone, temperature extremes, rain and snow. It has a long service life, and it was designed to perform between -60°C to 200°C (-76°F to 392°F).

USES: •Repair material for metal and SPF roofs •Seal fasteners, seams and details on low and semi-steep sloped roofs •Pipe penetrations through roof decks in metal flashings •Concrete, metal and most construction substrates •Mold and mildew resistance

SURFACE PREPARATION: All penetrations must be clean, dry and free of contaminants before PRODUCT NO. 910 FLASHING SEALANT is applied. Dust and loose particles must be blown out of the joint with oil-free compressed air, moving only in one direction. An oily surface may reduce adhesion.

APPLICATION: Always test adhesion before applying to different substrates. PRODUCT NO. 910 FLASHING SEALANT is ready-to-use and requires no mixing or additives. Apply PRODUCT NO. 910 FLASHING SEALANT to roofing substrate, fastener or penetration using appropriate caulking gun, brush, trowel, joint knife or plastic spatula to achieve a uniform membrane over the transition surfaces. Top coat with PRODUCT NO. 990 FOREVER-COAT Silicone Roof coating when dry to touch. PRODUCT NO. 910 FLASHING SEALANT can be applied in a single coat. Spread uncured PRODUCT NO. 910 FLASHING SEALANT to extend a minimum of 4” (100 mm) over the surface of the roof. Regularly monitor wet film thickness during application to ensure adequate uniform coverage. Coverage may vary depending on application technique and nature of substrate. Curing begins as soon as the sealant comes in contact with air. Application at temperatures below 4°C (40°F) will slow curing, while increased levels of humidity will aid curing. Tooling should be done before skin-over takes place. Remove wet material from application/spreading tool with a rag before the material cures. Carefully use appropriate cleaning agent, such as citrus solvent or odorless mineral spirits, to remove cured material from tools. For best results, follow precautions on packaging.

STORAGE: PRODUCT NO. 910 FLASHING SEALANT, when stored in original, unopened container in dry, shaded conditions, away from sources of heat or ignition, and stored below 32°C (90°F), has a shelf life of 12 months from date of manufacture.

HANDLING PRECAUTIONS: Product safety information required for safe use is not included. Before handling, read product safety data sheets and container labels for safe use and health hazard information. Safety data sheets are available on the TRC website at: www. rubberized.com.

PHYSICAL PROPERTIES: 100% Silcone Flashing Sealant Durometer Hardness 43 points (ASTM D2240, Shore A) Tensile Strength 160 psi (11 kg/cm² ) (ASTM D412) Elongation at Break 67% (ASTM D412) Tear Resistance 27 ppi (4.7 kN/m) (ASTM D624, Die B)

*NOTE: Percentages stated are + or -5% Approx. Shipping Weights: (All approximate weights include container) weight per gallon approximately 14 lbs.

LIMITED WARRANTY AND DISCLAIMER: To the best of our knowledge, the technical data contained herein is true and accurate at the date of issuance and is subject to change without prior notice. User must contact Tucson Rubberized Coatings to verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. Liability, if any, is limited to replacement of product unless installed by an approved contractor in accordance with Tucson Rubberized Coatings warranty procedures and program. For limited manufacturerʼs warranty and disclaimer information, visit our website at: www.rubberized.com.

DESCRIPTION. Enviro-Coat Roof Coating is a 100% acrylic roof coating that creates a durable sun reflective coating. The high reflective value of this acrylic topcoat helps to reduce interior temperature and protects the roof and roofing membrane by reducing heat absorption, asphalt oxidation and rapid thermal dimensional changes. It also decreases the chance of excessive loads being placed on cooling equipment.

USES. Enviro-Coat Roof Coating is specially designed to provide a tough weather resistant and decorative finish for mobile home tile and bituminous roof surfaces. This acrylic topcoat may be used over degreased or weathered aluminum, galvanized steel, primed steel, treated unweathered or weathered concrete. It can also be used on cured cold applied asphalt coatings, smooth surface roofings, and most prepared mineral surfaced roofings. This product can be directly applied over most previously white-coated sound roof surfaces.

SURFACE PREPARATION. A clean surface is absolutely essential for proper adhesion of this acrylic topcoat. In order to ensure a clean surface, follow these instructions.

(1) Previously coated surfaces: All dirt and unsound accumulations must be removed. Thus, you can use TSP to remove any mildew or algae which may be present. Rinse with water. Where necessary, use a broom and high pressure water hosing in order to clean the base surface. Allow water to completely dry before proceeding. Roof substrate must drain within 48 hours.

(2) Built-up Roofing: Must be 6 months or older. Clean and prime first with 1 gallon per 100 square feet of PRODUCT NO. 210, before application of finished white surfacing.

(3) Granule Surface: Must be clean, sound surface with no loose or foreign material.

(4) Rusty metal must be cleaned with a wire brush and primed with PRODUCT NO. 101. Asphalt primer prior to application of PRODUCT NO. 210 emulsion and PRODUCT NO. 302 Enviro-Coat Roof Coating. All fasteners must be tightly secured or replaced and encapsulated with PRODUCT NO. 501-W Patching Compound. In addition, all roof seams and flashings must be covered with PRODUCT NO. 501-W Patching Compound and membrane reinforcement.

APPLICATION. Stir in container until uniform in color and consistency. For Brushing: Use a soft nylon bristle broom or brush and apply with long even strokes. Avoid over-brushing. Do not attempt to retouch while film is drying. Wait until cured before applying second coat. For Roller: Medium to long nap for textured or rough surfaces. For Spray: Airless spray system with a minimum working pressure of 3000 PSI. Coverage rates will vary depending on porosity of surface as well as roof pitch. One coat can suffice, however, two coats are recommended for maximum reflectivity, durability and life cycle. Recommended application is two coats applied at right angles to previous coat by brush, roller or spray. First coat must dry before second coat is applied.

During application, keep tools clean and free from coating build up by rinsing frequently with water. Do not apply over uncured cold applied asphalt coating, wooden shingles, shakes, flood coats of hot melt asphalt or coal tar, or bare or rusted steel. Asphalt must be dull, not glossy. Do not apply unless temperature is 50°F and rising. Do not apply when rain or frost is forecast within 24 hours after application. In addition, conditions of high humidity will prevent curing in the usual four hours. Avoid heavy foot traffic.

RECOMMENDED COVERAGE RATES. (1) Mineral Surfaced Roll Roofing – 3 gal/ 100 sq. ft.; (2) Metal Roofing – 1 to 2 gal/100 sq. ft.; (3) Concrete Tile or Smooth Roll Roofing – 1.5 to 2 gal/100 sq. ft. (4) Re-coats 2 gallons per 100 sq. ft.

KEEP PRODUCT FROM FREEZING.

DO NOT APPLY TO ANY SURFACES THAT CONTAIN SILICONE.

CLEAN-UP. Use soapy water in order to clean brushes, tools and other equipment immediately after use. However, dried film may require paint remover.

Weight67542.2655460
Dimensions15 × 15 × 18 cm15 × 15 × 18 cm15 × 15 × 18 cm15 × 15 × 18 cm15 × 15 × 18 cm60 × 14 × 14 cm
Additional information
Weight 67 kg
Dimensions 15 × 15 × 18 cm
Weight per Gallon

10.9 lbs

Solids by Weight*

66%

Drying Time (At 50% relative humidity and 70°F)

Touch: 4 hrs, Firm: 24 hrs

Flammability

None

VOC

< 50 g/I

Viscosity

>160 KU

*NOTE:

Percentages stated are + or – 5%

Approx. Shipping Weights:

(All approximate weights include container)
5 gallon bucket weight approximately 58 lbs.

Color

Tan, White

Size

1 Gallon, 3.5 Gallon, 5 Gallon

Weight 54 kg
Dimensions 15 × 15 × 18 cm
Weight per Gallon

8.9 lbs

Solids by Weight*

38%

Drying Time (50% Relative Humidity & 70°F)

Touch/2 hrs – Firm/4 hrs minimum

Flammability

None

Wet Film

None

VOC

< 150 grams/liter

Elongation

>300%

Tensile Strength

450 PSI

Viscosity

115 – 125 KU

*NOTE:

Percentages stated are + or – 5%

Approx. Shipping Weights:

(All approximate weights include container)
5 gallon bucket weight approximately 50 lbs

Color

Off-White

Size

5 Gallon

Solids by Volume (%)

34%

Silicone (%)

None

Tear Resistance

> 120 lbf/in.

Water Swelling After 7 days

< 15%

Weight 2.2 kg
Dimensions 15 × 15 × 18 cm
Color

White

Size

4" x 324', 6" x 324', 12" x 324', 20" x 324', 40" x 324'

Weight 65 kg
Dimensions 15 × 15 × 18 cm
Durometer Hardness

43 points

Tensile Strength

160 psi (11 kg/cm² )

Elongation at Break

67%

Tear Resistance

27 ppi (4.7 kN/m)

Color

White

Size

5 Gallon

Weight 54 kg
Dimensions 15 × 15 × 18 cm
Weight per Gallon

10.5 lbs

Solids by Weight*

56%

Drying Time (50% Relative Humidity & 70°F)

Touch/2 hrs – Firm/4 hrs minimum

Flammability

None

Wet Film

None

VOC

< 150 grams/liter

Elongation

>200%

Tensile Strength

300 PSI

Viscosity

100 KU

*NOTE:

Percentages stated are + or – 5%

Approx. Shipping Weights:

(All approximate weights include container)
5 gallons 54 lbs.

Color

Tan, White

Size

5 Gallon

Weight 60 kg
Dimensions 60 × 14 × 14 cm