PREMIER 4″ FLAT SASH PAINT BRUSH

  • Polyester bristles provide superior control
  • Durable and easy to clean
  • Can be used with interior or exterior paints
Premier 4in Paint Brush

$4.99

Login / Register for Additional Discounts

  • Polyester bristles provide superior control
  • Durable and easy to clean
  • Can be used with interior or exterior paints
In Stock. Ready for Delivery.

Description

DESCRIPTION: Provides a superb finish at an attractive price. Polyester bristles allow you to apply paint with superior control.

Can be used with interior or exterior paints.

Additional information

Weight 0.4 kg
Dimensions 12 × 12 × 12 cm

Quick Comparison

SettingsPREMIER 4" FLAT SASH PAINT BRUSH removeSelf-Adhesive Base Ply Membrane TRC 950-B removeL PRO SOLUTION 9" PAINT ROLL COVER - 1.25" NAP removePRODUCT NO 297-X ULTIMATE ADHESION ACRYLIC PRIMER removeTIETEX POLYESTER ROOFING MEMBRANE - REINFORCEMENT ROOFING FABRIC removePRODUCT 600-T RUBBERIZED STUCCO remove
ImagePremier 4in Paint Brush950b productLPRO 9in Roll Coverproduct 297TietexaTuff Tex Rubberized synthetic stucco product no 600-T
SKUPBFSB4RC9-1.25297-x324W4600-TW5
Rating
Price$4.99

Login / Register for Additional Discounts

$140.00

Login / Register for Additional Discounts

$4.99

Login / Register for Additional Discounts

From $25.00

Login / Register for Additional Discounts

From $26.50

Login / Register for Additional Discounts

$69.00

Login / Register for Additional Discounts

Stock
Availability
Add to cart

Add to cart

Add to cart

Add to cart

Buying Options

Buying Options

Add to cart

Description
  • Polyester bristles provide superior control
  • Durable and easy to clean
  • Can be used with interior or exterior paints
TRC 950-B is a self-adhesive base ply membrane composed of SBS modified bitumen. The surface is a UV-resistant tri-laminated woven polyethylene, while the self-adhesive underface is covered with a split-back silicone release film.
  • 1-1/4" Nap
  • High Density Polyester Fabric
  • For Extra-Rough Surfaces
  • For All Primers & Flat Paints
  • Creates a waterproofing membrane for areas with frequent standing water
  • X-TREME adhesion primer for a variety of substrates including new and aged EPDM, TPO, and Spray Polyurethane Foam
  • Excellent bleed block resistance to eliminate top coat discoloration over asphalt
  • Which primer is right for me
  • 4" x 324'
  • 6" x 324'
  • 12" x 324'
  • 20" x 324'
  • 40" x 324'
  • Tietex polyester fabric is a stitch-bonded, high-performance fabric
  • Used in applied built-up roofing and roof maintenance systems using either water-based asphalt, acrylic emulsions, or solvent type coatings or mastic
  • The polyester fabric is white with lay lines for one and two-ply roof systems
  • Creates a thick textured rubber-like shield of protection
  • Insulates and resists cracking and chipping
  • Will adhere to any primed surface
  • White can be tinted for an extra charge (Available in-store only)
  • 15-Year limited manufacturers warranty
Content

DESCRIPTION: Provides a superb finish at an attractive price. Polyester bristles allow you to apply paint with superior control.

Can be used with interior or exterior paints.

DESCRIPTION: Professional-grade, 9" roller cover with high density polyester fabric for all Primers and Flat paints.

DESCRIPTION. PRODUCT NO. 297-X X-TREME is a stain resistant, highly adhesive primer for new and existing roofing systems. PRODUCT NO. 297-X X-TREME is a waterproof membrane ideal for areas with low spots that are prone to standing water. PRODUCT NO. 297-X X-TREME should be used as a base coat, not being left exposed to the suns UV rays for extended periods of time.

USES. PRODUCT NO. 297-X X-TREME is to be used as a base coat primer over most substrates including EPDM, TPO, PVC, spray polyurethane foam, Hypalon, asphalt, tar, hot-applied built-up roofing, granulated cap sheet, steel, and aluminum roofing substrates. PRODUCT NO. 297-X X-TREME is not recommended to be used as a fabric saturant when installing fabric overlay systems.

SURFACE PREPARATION. Roof substrates must be clean, dry, free of all debris, and any contaminates which would impede proper adhesion. A pressure wash is recommended, if a pressure washer is not available a cleaning agent should be used in conjunction with hose and broom washing. In addition to pressure washing, a wire brush should be used to remove any surface rust on metal roofing systems. Metal panels where the structural integrity has been compromised should be removed and replaced with like panels. A bleach and water solution (1 part bleach to 2 parts water) should be used to treat any roof areas that have mildew or algae. All roof surfaces should be thoroughly cleaned and allowed to dry completely prior to application of any Tucson Rubberized Coatings restoration products

APPLICATION. Proper protective clothing and PPE should be worn when applying products. It is normal to see a small amount of separation when first opening a pail. If necessary, gently mix the product with a roller frame or paddle mixer, being careful to not introduce air into the product during mixing. Product can be applied by roller (3/8 - 3/4" nap), brush, and spray equipment capable of 2000 - 3000 PSI and 1 - 3 GPM of output. For best results when spraying, an 8-28 - 8-31 reversible spray is recommended. Do not dilute product. Tucson Rubberized Coatings Products should not be applied when freezing temperatures or rain is expected within 24 hours of completed application. During application, roof surface temperatures should be between 40 and 115 degrees Fahrenheit, with no moisture present. PRODUCT NO. 297-X X- TREME must be coated within 24 - 48 hours to avoid premature film degradation.

RECOMMENDED COVERAGE RATES (completed in 1 coats): Product should be applied at a minimum rate of .5 - .75 gallon per 100 square feet of roof surface, per coat. to avoid prolonged cure times, PRODUCT NO. 670 X-TREME should not be applied at a rate greater than 1 gallon per 100 square feet of roof surface per coat. Coverage rates will depend on the porosity of the roofing substrate

DO NOT APPLY TO ANY SURFACES THAT CONTAIN SILICONE.

STORAGE: Product should be stored in a clean and dry area, away from direct sunlight and protected from freezing.

CLEAN-UP. Clean brushes, tools, and other equipment with warm soapy water immediately after use. Dried film may require paint remover.

HANDLING PRECAUTIONS: Product safety information required for safe use is not included. Before handling, read product safety data sheets and container labels for safe use and health hazard information. Safety data sheets are available on the TRC website at: www.rubberized.com.

LIMITED WARRANTY AND DISCLAIMER: To the best of our knowledge, the technical data contained herein is true and accurate at the date of issuance and is subject to change without prior notice. User must contact Tucson Rubberized Coatings to verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. Liability, if any, is limited to replacement of product unless installed by an approved contractor in accordance with Tucson Rubberized Coatings warranty procedures and program. For limited manufacturer's warranty and disclaimer information, visit our website at: www.rubberized.com.

SIZE. 4" x 324'

DESCRIPTION. Tietex polyester roofing membrane is a reinforcement roofing fabric that is white with lay lines for one and two-ply roof systems. It offers an unusual combination of high-strength properties, and it also delivers good elongation for excellent thermal stress force accommodations.

USES. Tietex polyester fabric is a stitch-bonded, high-performance fabric for use in applied built-up roofing and roof maintenance systems using either water-based asphalt, acrylic emulsions, or solvent type coatings or mastic.

Made in the USA. If you would like to learn more about this exceptional roofing product, then get in touch with Tucson Rubberized Coatings today. We will be glad to answer your questions. If you need help finding the right coating product, then our team can help!

DESCRIPTION. PRODUCT NO. 600-T creates a thick rubber-like shield of protection which is highly resistant to cracking or chipping. This rubberized stucco product also contains bonding agents which give it excellent adhesion and ceramics for insulating properties.

USES. This rubberized stucco product is excellent for use as a complete interior or exterior wall finish, as well as for repairing existing walls. It is paintable, or you may also have it pre-tinted to a color of your choice to eliminate expensive repainting. PRODUCT NO. 600-T can be applied in various types of finishes and is ideal for beautifying virtually any surface, such as existing stucco, masonry, block, brick, metal, plywood, OSB, or wood siding.

SURFACE PREPARATION. All surfaces must be dry and free of dust, oil, loose granules, or peeling paint and all other foreign matter. You can use wire brushing, sanding, or power washing in order to prepare the surface. All cracks, joints, or uneven surfaces should be filled with PRODUCT NO. 501-W-P Patching Compound or PRODUCT NO. 400 Smooth Base Coat can be applied prior to applying PRODUCT NO. 600-T for filling hairline cracks, waterproofing, and providing additional insulation.

APPLICATION. Power mix product to an even mixture, then apply to surface with a stiff brush, roller, trowel, or hopper gun depending on the desired surface. Keep the brush or roller moist for easy application. If you want a thinner texture, then reduce viscosity with PRODUCT NO. 290 Surface Bonder. Apply PRODUCT NO. 600-T at a rate of 5-8 gallons per 100 sq. ft., depending on the desired thickness and finish. This product should not be applied when rain or frost is forecasted within 24 hours. Apply only when the temperature is 55 degrees and rising.

KEEP PRODUCT FROM FREEZING

CLEAN-UP. Clean brushes, tools, and other equipment with soapy water immediately after use.

Weight0.4600.15542.280
Dimensions12 × 12 × 12 cm60 × 14 × 14 cm12 × 12 × 12 cm15 × 15 × 18 cm15 × 15 × 18 cm15 × 15 × 18 cm
Additional information
Weight 0.4 kg
Dimensions 12 × 12 × 12 cm
Weight 60 kg
Dimensions 60 × 14 × 14 cm
Thickness

40 mil (1.0 mm)

Dimensions

39 in × 65 ft (1 m × 20 m)

Gross/Net Coverage

213 sq ft (20 sq m) / 194 sq ft (18 sq m)

Roll Weight

40 lb (20 kg)

Surface

Tri-laminated Woven polyethylene

Underface

Self-adhesive, covered with a split-back silicone release film

Weight 0.15 kg
Dimensions 12 × 12 × 12 cm
Weight 54 kg
Dimensions 15 × 15 × 18 cm
Weight per Gallon

8.5 lbs

Solids by Weight*

49%

Drying Time (50% Relative Humidity & 70°F)

Touch: 4 hrs, Firm: 12 hrs

Flammability

None

VOC

< 50 g/I

Viscosity

85 – 95 KU

*NOTE:

Percentages stated are + or – 5%

Approx. Shipping Weights:

(All approximate weights include container)
5 gallon bucket weight approximately 48 lbs.

Color

Off-White

Size

5 Gallon, 1 Gallon

Solids by Volume

49%

Silicone

None

Weight 2.2 kg
Dimensions 15 × 15 × 18 cm
Color

White

Size

4" x 324', 6" x 324', 12" x 324', 20" x 324', 40" x 324'

Weight 80 kg
Dimensions 15 × 15 × 18 cm
Weight per Gallon

15.7 lbs

Solids by Weight*

79%

Drying Time (50% Relative Humidity & 70°F)

Touch/2-3 hrs

Flammability

None

VOC

< 150 grams/liter

Viscosity

120 KU

*NOTE:

Percentages stated are + or – 5%

Approx. Shipping Weights:

(All approximate weights include container)
5 gallons 80 lbs.

Color

White

Size

5 Gallon