| And Many More product
are available, including asphalt primers and emulsions, patching compounds, reinforced
membranes, puddle fillers, tools and accessories. | 
|
Product 6000 Specification Sheet
DESCRIPTION: Dura-Coat roof coating is
an ultra-white 100% acrylic elastomeric roof coating. A premium grade coating
designed for maximum protection against sun and weather. Its bright finish enables
it to reflect the sun's heat and harmful UV rays. This product forms a thick,
rubber-like shield that expands and contracts over 300% to prevent roof damage.
It resists cracking, peeling, and mildew while offering unbeatable weatherproof
protection and excellent resistance to lifting under ponding water conditions.
USES: Dura-Coat roof coating can be used over
mineral surface roofing, aged aluminum, tar, asphalt, or hot-applied built-up
roofing after application of Product #210 emulsion. All large cracks and seams
should be reinforced with woven glass fabric embedded into Product #210. (on E.P.D.M.
roofs, embed membrane over any large crack or seams into Product #6000). This
product can be directly applied over most previously white-coated sound roof surfaces.
Product #6000 is highly recommended for E.P.D.M. roofs or areas subject to unusually
severe moisture conditions such as valleys, around roof drains, low spots or in
any area where water is expected to be trapped on a roof.
SURFACE
PREPARATION: All surfaces must be dry and free of dust, oil loose granules,
gravel or peeling paint and all other foriegn matter. Rusty metal must be cleaned
with a wire brush and primed with Product #101 Asphalt primer prior to application
of Product #210 emulsion and Product #6000 Dura-Coat roof coating. Polyurethane
Foam Roofs: Prime surface with #295 Surface conditioner prior to application of
Product #6000. Pressure washing surfaces is recommended for best results. Surfaces
with any mildew growth or stains should be cleaned with a bleach solution (2 parts
water to one part bleach) prior to applying this product. Be certain all surfaces
are thouroughly rinsed and dry prior to applying coating.
APPLICATION:
Material should be stirred in the container and applyed by a soft bristle brush
or broom, a long nap roller or suitable spray equipment. Airless spray system
with a minimum working pressure of 3000 PSI. Coverage rates will vary depending
on porosity of surface as well as roof pitch. Recommended application is two coats
applied at right angles to previous coat by brush, roller or spray for maximum
reflectivity, durability and life cycles. First coat must dry before second coat
is applied. During application, keep tools clean and free from coating build up
by rinsing frequently with water. Adequate protection for most surfaces is obtained
by the use of two gallons of Dura-Coat Roof Coating per 100 sq. ft. applied in
two coats. As a complete roofing tystiem this product should be applied at a rate
of 5 gallons per 100 sp. ft. applied in two coats. Allow 24 to72 hours depending
on weather conditions and applications rate of curing prior to application of
second coat. Do not apply unless temperature is 55°F and rising. Do not apply
when rain or frost is forecast within 24 hours after application. Conditions of
high humidity will prevent curing in the usual four hours. Avoid heavy foot traffic.
KEEP PRODUCT FROM FREEZING
CLEAN-UP:
Clean brushes, tools and other equipment with soapy water immediately after use.
Dried film may require paint remover.
PHYSICAL PROPERTIES:
Solids by Weight: 74%.; Weight per Gallon: 11.4lbs.; Drying Time at 50% Relative
Humidity & 70°F: Touch: 2.5 hours, Firm: 5 hours; Flammability: Wet Film:
None; VOC: <150 grams/liter; Elongation: 300%; Tensile Strength: 300 PSI; Viscosity:
6500 CPS(± 500) 
Roofing
Products | Stucco & Wall Coatings | Complete
Roofing Systems
Applying Stucco & Wall Coatings
| Re-coating Your Roof | Home E-mail:
info@rubberized.com Copyright
© 2005 - Tucson Rubberized Coatings |